sdkm-LOGO

Steel structure dairy farm: advantages and standardized design layout guide

Home / Single Post

Table of Contents

Advantages of steel structure dairy farms

Superior structural performance

High strength: Steel has strong compression and bending resistance, suitable for large span space, and convenient for mechanized operation.

Seismic and windproof: Steel structure has good toughness and can withstand bad weather (such as typhoons and blizzards).

Efficient construction

Modular construction: prefabricated components in the factory, assembled on site, and the construction period is shortened by 30%-50% compared with traditional buildings.

Not affected by seasons: Construction can still be carried out in winter, reducing delays caused by weather.

Significant economic efficiency

Low long-term cost: Although the initial investment is slightly higher, the maintenance cost is low (it can be used for more than 20 years after corrosion resistance treatment).

High space utilization: The column-free design increases the stocking density and reduces the unit cost.

Environmentally friendly and sustainable

Recyclable: The steel recycling rate after demolition exceeds 90%, reducing construction waste.

Energy-saving design: Lighting belts and ventilation systems can be integrated to reduce energy consumption.

Convenient hygiene management

Smooth surface: not easy to breed bacteria, easy to wash and disinfect with high-pressure water gun.

Cut steel structure costs with smart design and modular efficiency.

 Key points of standard design layout

Zoning planning

Production area (core area):

Cowshed: designed according to lactating cows, dry cows, calves, and young cows. Lactating cowshed is preferably close to the milking parlor.

Milking parlor: located in the center to shorten the walking distance of cows (common herringbone or turntable layout).

Auxiliary area:

Feed warehouse: close to the entrance of the field for easy transportation; TMR mixing station is adjacent to the cowshed.

Manure treatment area: downwind location, equipped with biogas digester or solid-liquid separation equipment.

Manure treatment area: office, veterinary room, etc. are located in the upwind direction, keeping a sanitary distance from the production area.

Cowshed design standards

Size:

The span of a single cowshed is usually 12-18 meters (natural ventilation) or 20-30 meters (mechanical ventilation).

Lactating cow bed size: 1.2-1.3m × 2.4-2.5m/head, channel width 3-4m (to meet equipment access).

Ventilation and lighting:

Open side wall + roof ventilator (ammonia concentration controlled at <10ppm).

Lighting area ≥15% (PC board lighting belt can be set on the roof).

Ground:

Bed material (sand or rubber mat), anti-slip concrete in the channel (slope 2%-3% for drainage).

Structural details

Steel selection:

Q345B steel is used for the main frame, and galvanized C-shaped steel is used for the purlin (anti-corrosion coating ≥275g/m²).

Roof design:

Double slope roof (slope 10%-15%) to avoid water accumulation; insulation layer can be installed in high temperature areas in summer.

Environmental control

Cooling: fan + sprinkler system (the temperature of the lactating cow house should be controlled at ≤25℃).

Sewage discharge:

Slatted floor + manure scraper (2-3 times a day), or fermentation bed mode.

Biosafety

Clean and dirty diversion: Set up clean channels (feed transportation) and dirty channels (manure and sewage transportation) to separate.

Disinfection facilities: Disinfection pools and vehicle spray devices are set up at the entrance.

Conclusion

Steel structure dairy farms are gradually replacing traditional construction models with their advantages such as high efficiency, durability and environmental protection. Through scientific planning and layout, and optimized environmental control, dairy cow welfare (reducing heat stress) and milk production efficiency (increasing unit yield by 5%-10%) can be significantly improved, while reducing long-term operating costs. It is recommended that breeding companies consult a professional team before construction and conduct customized design based on their own needs to maximize benefits.

Facebook
Twitter
LinkedIn

Leave a Reply

Your email address will not be published. Required fields are marked *

latets blog

wanted to work with us ?

Please feel free contact SDKM team.

Subscribe For our newsletter.

Share The Article

Facebook
Twitter
LinkedIn

We are always ready for your needs & questions.

Contact Us